After placing the machine tool in position, remove the packaging film and oil paper from it. Remove the accessories fixed to the backgauge. Be sure to remove the oil paper from the ball screw.

Take out the front material support from the wooden box accessories and install it onto the machine tool. Remove the protective film from the side guard rails, and install them on both sides of the machine tool.

Remove the protective film from the oil cylinder cover. Assemble the sheet metal of the oil cylinder cover as a whole. Connect the lighting power cable of the oil cylinder cover sheet metal assembly according to the correct color.

Take out the foot switch from the wooden box accessories and remove its packing film. Connect the foot switch plug to the electrical cabinet. Take out the valve from the wooden box accessories (removed for shipping height). If you encounter any issues during this stage, feel free to contact us or check our Complete Guide to Press Brake Installation for step-by-step assistance.

Remove the waterproof and dustproof cover plate on the top of the Y1 oil cylinder. Check whether the sealing ring of the Y1 proportional valve is intact. Install the Y1 proportional valve synchronizing block and the required connecting oil pipes. Fix the pipe clamps.

Insert the Y1 synchronizing block control plugs and feedback plugs according to the plug numbers marked at the factory. Plug in the feedback plug.

Plug in control plug No. 4. Plug in control plug No. 5. Plug in control plug No. 6. Secure the control plugs. Installation complete. Remove the waterproof and dustproof cover plate on the top of the Y2 oil cylinder. Check whether the sealing ring of the Y2 proportional valve is intact.

Install the Y2 proportional valve synchronizing block and the required connecting oil pipes. Install the control plugs and feedback plugs of the Y2 synchronizing block.

Plug in the feedback plug. Plug in control plug No. 1. Plug in control plug No. 2. Plug in control plug No. 3. Secure the control plugs. Secure the pipe clamps on the Y2 synchronizing block side.

Check whether any pipe joints are loose, and tighten all oil pipe connections. Install the pressure valve on the pressure block. Install the two-position four-way control valve on the pressure block. Check that the sealing rings are properly installed. You can also refer to our Brochures for detailed assembly diagrams and specifications.

Proceed to install the two-position four-way control valve on the pressure block. Install the valve plug on the pressure block. Install the feedback plug on the pressure block. Installation complete. Remove the fixing screws of the oil cylinder cover.

Hoist the oil cylinder cover and install it onto the machine tool. Installation complete. Connect the lighting power cables from the oil cylinder cover to those coming from the electrical cabinet according to their colors.

Installation complete. Wipe off any dust and footprints left during the machine tool installation with a cloth. Find the electrical cabinet key from the wooden box accessories and open the cabinet. Connect the appropriate power cable and ground wire according to the machine tool voltage.

Open the air filter, add the hydraulic oil needed for the machine tool (generally No. 46 anti-wear hydraulic oil). Refer to the data provided by the factory for the amount to be added. Turn on the main power switch. If the machine is equipped with a main motor servo

Observe whether the phase sequence protection switch indicator lights up inside the electrical cabinet. If the indicator does not light up. If the indicator does not light up, adjust the incoming power supply phase sequence (swap any two power lines).

If the phase sequence protection switch indicator is lit, you may proceed to the next step. Close the electrical cabinet door and start the oil pump. If the machine has a main motor AC motor (without phase sequence protection switch).

Start the power, then turn it off. Observe if the motor fan blade rotates clockwise. If it rotates clockwise, proceed to the next step. If it rotates counterclockwise. Adjust the incoming power supply phase sequence (swap any two power lines).

For a main motor servo system, confirm the phase sequence protection is on. For a main motor AC motor, confirm the motor rotates clockwise. Then we can start the machine tool’s oil pump. Go to the operating system interface.

First, set the language. Click "Settings". Find the required language. For example, select English. Then enter the manual interface, check whether the manual interface parameters and mold settings are correct. If everything is correct, press the system start button, the machine tool will find the reference point for all axes.

When all axes have found their reference points, and the upper mold has lifted, go to the system interface, set the workbench deflection compensation to 0, keeping the workbench in a straight line, then press the "Run" button.

Next, adjust the machine tool level. Place the level gauge in the middle of the lower die. Observe the position of the bubble. Remove the mold protection mold. For a new machine just oiled and powered on, air may be present in the hydraulic pipelines.

Run up and down empty cycles more than 20 times to discharge the air from the system. Now we can proceed with normal programming. Click "Product". Click "New Program". Enter ADH-001. Enter the thickness of the sheet to be bent: 1.2 mm.

Select the upper and lower dies. The press brake is using these two molds. Proceed to the next programming step. Enter the length of the sheet to be bent: 2000 mm. Bend to 90°. First step: bend 15 mm. Add another step.

Second step: bend 25 mm. Enter automatic mode. Start bending. Bending in progress. Bending completed. Our press brake has gone through installation, oil-filling, power connection, and trial operation, and has completed a bending task.

Our press brake can now officially be put into production. Thank you all for watching press brake operation demonstration. For further technical details or model options, please contact us.